Underfloor heating in Stratford-upon-Avon
Warm floors, no radiators on the wall and even heat right across the room. We install and repair wet underfloor heating across Stratford-upon-Avon and the surrounding Warwickshire area, retrofits, new builds and extensions.
No call-out fee on booked jobs · Written price before any work starts · Same day where we can
Stratford-upon-Avon, Warwickshire
Underfloor heating in Stratford-upon-Avon
Underfloor Heating in Stratford-upon-Avon covers a wide range of situations, from a straightforward planned visit through to a system that has failed completely. We handle both, and we are honest about which category your job falls into. We protect floors and worktops while we work and clear up properly afterwards. It sounds obvious, but it is the thing customers in Stratford-upon-Avon mention most.
Property context
Housing across Stratford-upon-Avon varies enough that no two jobs are quite the same. Older properties often hide a mix of copper, plastic and imperial pipework, while newer homes tend to run sealed systems with unvented cylinders.
Heating in the area
Most heating work in Stratford-upon-Avon is gas, and we service, repair and install condensing combi, system and heat-only boilers from the main manufacturers. Properties off the gas grid are usually on oil, and we cover Grant, Firebird, Warmflow and Worcester oil boilers too.
Plumbing in the area
We handle day to day plumbing repairs in Stratford-upon-Avon alongside larger projects such as bathrooms, ensuites, cylinder replacements and mains water boosters.
Postcodes we cover around Stratford-upon-Avon
- CV37
Also covering near Stratford-upon-Avon
Accredited & approved
Registered engineers, manufacturer-approved brands
Stratford-upon-Avon underfloor heating
Even warmth, no radiators, quiet in the background
Wet underfloor heating is the gold standard for downstairs open-plan spaces and kitchen extensions. It's efficient, comfortable and frees the walls for something more useful than a panel radiator. Serving Stratford-upon-Avon and the surrounding Warwickshire area.
For new builds we design the loops, manifolds and controls from scratch. For retrofits we use low-profile overlay systems (Nu-Heat LoPro, Wunda) that add 15-20mm to the finished floor, quick to install and no lifting of joists.
For repairs, the majority of UFH faults sit at the manifold or the wiring centre, failed actuators, seized pumps, wrong flow temperatures. Actual leaks in the pipe are rare and we can pressure-test to find them if needed.
Common signs to look out for
- Cold zones on a UFH loop
- Actuator that stays open or closed
- Wiring centre calling for heat with no response
- Screed hot but floor above cold
- Retrofitting UFH into an existing room
- New extension or kitchen refit
Kitchen or extension?
Get UFH designed round your project
Speak to a real Warwickshire engineer, no call centres.
Gas Safe registered engineers, workmanship guaranteed.
Local · Trusted · Insured
Our work
Recent jobs across Warwickshire
A snapshot of the work we've completed lately, tidy, guaranteed and signed off end-to-end.
How we work
A simple, honest process
- 1
Design
Loop layout, flow rates and manifold sized to the room.
- 2
Install
Pipe laid, manifold plumbed in, controls wired.
- 3
Commission
Pressure-tested, air removed, flow rates set per loop.
- 4
Set up controls
Room thermostats zoned back to the manifold, boiler flow temp set correctly.
Extension coming up?
Get a UFH design and quote
Retrofit vs new build
Which UFH system suits your project
Retrofit overlay is right when...
- Existing floor can take an extra 15-20mm
- Doors can be trimmed to suit
- Room is downstairs, on a solid or timber base
- You want to avoid lifting joists
Screed / new-build UFH when...
- New extension, kitchen or garden room
- Solid ground floor being poured anyway
- You want deep thermal mass for even heat
- Whole-floor coverage across multiple rooms
Kitchen or extension?
Get UFH designed round your project
Speak to a real Warwickshire engineer, no call centres.
The manifold matters
Where 90% of UFH problems live
- Failed actuators (the little motors on each loop)
- Pump seized or wrong speed setting
- Blending valve set to wrong flow temp
- Wiring centre miswired or fused
- Air trapped in a loop, cold floor above hot manifold
- Loops unbalanced, some hot, some cold
- Room stat wired to the wrong loop
Kitchen or extension?
Get UFH designed round your project
Speak to a real Warwickshire engineer, no call centres.
What customers say
Trusted by Warwickshire homeowners
Read all 85+ reviews5.0 / 5
Based on 85+ Google reviews
"Replaced our ageing boiler and rebalanced the whole system. Quiet, efficient, and the radiators have never been hotter. Exceptional service from start to finish."E. HargreavesWarwick
"Installed underfloor heating across our kitchen extension. Thoughtful planning, faultless finish. A real craftsman."H. ClarkeStratford-upon-Avon
"Fitted a new combi boiler and re-piped our airing cupboard. Immaculate workmanship and left the house spotless. Genuinely the best tradesman we've had."S. PatelLeamington Spa
Coverage
Also covering near Stratford-upon-Avon
Same-team engineers across the county. If your town isn't listed, give us a call, we cover most Warwickshire postcodes.
Answers
Frequently asked questions
The questions Stratford-upon-Avon homeowners ask us about wet underfloor heating.
Yes. Stratford-upon-Avon (CV37) is inside our normal service area and we cover it for underfloor heating throughout the year.
Yes. M&S Bespoke engineers are Gas Safe registered and fully insured, and all work is carried out to current regulations.
Call or message us with the details. For anything that needs assessing we will arrange a visit first so the figure we give you is accurate rather than a guess.
Yes. We work with private landlords and letting agents across Stratford-upon-Avon, and we can arrange access with tenants directly.
Yes, using low-profile overlay systems that raise the floor by around 15-20mm. We survey the room first.
Most modern condensing boilers pair with UFH well because the low return temperature suits condensing operation. We commission it correctly to protect the boiler.
Wet is more efficient long-term, uses your boiler and is better for whole floors. Electric is simpler for small rooms like en-suites but expensive to run.
Yes, most UFH faults are on the manifold, actuators or wiring centre rather than the pipe. We test and replace those first.
Yes, room-by-room thermostats zoned back to the manifold, the standard Nu-Heat / Uponor set-up. We wire and commission it properly.
Send us the details
Request a straight-talking quote
Tell us what's happening, brand, symptoms, how long, any fault codes. We'll come back with a clear price and next steps.
Ready when you are
Speak to a Warwickshire engineer
Call, WhatsApp or request a written quote, whichever is easiest.